Monthly Archives: November 2016

Building a simple delta numerical model: Part III

In this part of “Building a simple delta numerical model”, we’ll simply develop a module for calculating sediment transport at all locations within our model domain. This is naturally a critical piece of the model to get right, because the magnitude of sediment transport that occurs within the delta system will have a direct correlation with the magnitude of geomorphic change to the delta system. Just as before, we’ll be working our module for the Mississippi River, and so we will use the Engelund and Hansen, 1967 formulation for bed-material load sediment transport.

It is worth noting here that there are countless sediment transport equations published within the literature, with applicability for different scenarios, covering the entire range of alluvial rivers, the shelf environment, to turbidity currents. A nice review of some relations is given by Garcia, 2008, who produces the plot below with six selected relations, where τ* is shear stress (Shields number) and q* is a dimensionless sediment transport.

garcia_formulas

The only points I hope to make with this figure are that stress and transport are nonlinearly related, and that many of the relations are quite similar. In fact, the majority of sediment transport equations are based on an excess-shear stress formulation, where, as shown above, the sediment transport prediction scales with the shear stress. The Engelund and Hansen, 1967 equation is given in its dimensional form by (Equation 1)

eh_formula

where qs is the sediment transport per unit width (m2/s), β is an adjustment coefficient discussed below, R = 1.65 is submerged specific gravity of the bed sediment, = 9.81 m/s2 is gravitational acceleration, is the grain size in question, Cf is the coefficient of friction, ρ = 1000 kg/m3 is the fluid density, and τ = ρ Cf U2 is the fluid shear stress, where is depth-averaged fluid velocity.

The solution to this equation is obtained by simple algebra, and so I will display the code calculations below without any explanation.


U = Qw ./ (H .* B0); % velocity

function [qs] = get_transport(U, Cf, d50, Beta)
% return sediment transport at capacity per unit width
% 1000 = rho = fluid density
% 1.65 = R = submerged specific gravity
% 9.81 = g = gravitation acceleration
u_a = sqrt(Cf .* (U.^2));
tau = 1000 .* (u_a.^2);
qs = Beta .* sqrt(1.65 * 9.81 * d50) * d50 * (0.05 / Cf) .* ...

        (tau ./ (1000 * 1.65 * 9.81 * d50)) .^ 2.5;
end

Let’s first simply examine the behavior of Equation 1, in its dimensionalized form, for the Mississippi River. We need to define the grain size and adjustment coefficient to use in our model; we’ll follow from the literature and use 300 μm for the grain diameter, assuming this makes up the entirety of the bed, and β = 0.64 an empirical adjustment (Nittrouer et al., 2012; Nittrouer and Viparelli, 2014).

Evaluating the equation over a range of velocities from 0 to 3 m/s, we find that the nonlinear behavior shown in the above figure is also true for the Engelund and Hansen formulation.

 

Now, let us implement this into our delta model. Following from earlier, the flow depth and velocity are related by the cross sectional area and discharge, where for a rectangular cross section, the velocity = Qw / H B. We therefore can take our calculation of flow depth from the previous lesson, and solve for velocity at each location. We then simply plug this into the relation for τ given above and solve Equation 1.

 

The bottom plot reveals the behavior of the flow velocity calculated through the backwater region (shown in red), and the resulting sediment transport calculated (shown in green). The nonlinearity between stress (i.e., velocity) and transport is again revealed by the change in slope of the lines through the backwater region. Following from left to right along the green curve, it becomes obvious that there is a decrease in transport downstream. If there is more sediment being transported upstream than downstream, then there must be sediment that is deposited to the bed somewhere along the channel bed between ‘upstream’ and ‘downstream’.

This thought experiment represents one half of the famous Exner equation, which we will explore in the next part, and will provide the last module to complete our delta model. My complete code for the sediment transport calculation in our backwater delta model can be found here.

 

References

1. Engelund, F. & Hansen, E. A monograph on sediment transport in alluvial streams. (Technisk Vorlag, Copenhagen, Denmark, 1967).
2. García, M. H. Sediment Transport and Morphodynamics in Sedimentation engineering processes, measurements, modeling, and practice 21–163 (American Society of Civil Engineers, 2008).
3. Nittrouer et al., Spatial and temporal trends for water-flow velocity and bed-material sediment transport in the lower Mississippi River. 2012. Geological Society of America Bulletin, 5 (Table 1).
4. Nittrouer, J. A. & Viparelli, E. Sand as a stable and sustainable resource for nourishing the Mississippi River delta. Nature Geoscience, 7, 350–354 (2014).

This material is based upon work supported by the National Science Foundation (NSF) Graduate Research Fellowship under Grant No.145068 and NSF EAR-1427177. Any opinion, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation.

Building a simple delta numerical model: Part II

Taking the simpler form of the backwater equation, that is, assuming that width does not vary over the channel reach, we find an expression for changing flow depth along the channel streamwise coordinate x: (Equation 1)backwater_fixed_eqnwhere S is the channel bed slope, Cf  is the dimensionless coefficient of friction, and Fr is the Froude number: (Equation 2)

A couple quick notes about the overall delta model we are developing herein:

  1. The code for this entire model will be developed in Matlab syntax, however, the math is all just math, and the code could easily be translated to another programming language.
  2. The model will be set up for the conditions of the Mississippi River, to what I feel are the best constraints published in the literature. Surely not everyone will agree with some of my choices.

We set up our model domain by defining some parameters:

L = 1200e3; % length of domain (m)
nx = 400; % number of nodes (+1)
dx = L/nx; % length of each cell (m)
x = 0:dx:L; % define x-coordinates
start = 63; % pin-point to start eta from (m)
S0 = 7e-5; % bed slope
eta = linspace(start, start - S0*(nx*dx), nx+1); % channel bed values
H0 = 0; % fixed base level (m)
Cf = 0.0047; % friction coeff

bw_schem_label

Each of these terms are necessary for defining the boundary conditions the backwater calculation requires. We will additionally need to define the water discharge (Qw), and it’s width averaged derivative qw = Qw / B, where B is the channel width. We’ll use a fixed width of 1100 m (Nittrouer et al., 2012) and a discharge of 10,000 m3/s; since width is fixed in our model, qw = 31.8182 m2/s.

Finally, to solve the above backwater equation, we’ll need to find the local slope at all nodes — our bed holds a constant slope so we could just skip this step and send S0 directly into the calculation, but we’ll be wise beyond our present experience, and prepare our calculation now for the future when our bed slope is constantly changing in time and space. A simple slope calculation is completed by a central difference calculation, applying forward difference and backward difference calculations at the domain upstream and downstream boundaries, respectively.

function [S] = get_slope(eta, nx, dx)
% return slope of input bed (eta)
S = zeros(1,nx+1);
S(1) = (eta(1) - eta(2)) / dx;
S(2:nx) = (eta(1:nx-1) - eta(3:nx+1)) ./ (2*dx);
S(nx+1) = (eta(nx) - eta(nx+1)) / dx;
end

As described in the previous section, we will use a predictor-corrector scheme to find a solution to Equation 1. This is not meant to be a comprehensive guide on solving ODEs, and so I will only summarize the method here.

  1. We first can evaluate the flow depth H at the downstream boundary, where elevation is fixed (H = H0 – η = 21 m).
  2. Then we predict the value at the next upstream node by solving Equation 1 for dH/dx at our known downstream-most node, using the inputs described above and H and S at the known node. This yields dH/dxp = 6.5784e-05.
  3. Multiplying dH/dx by dx = 3000 m and subtracting this change from the known H at the downstream-most node, we find our predicted value Hp for the next upstream node.
  4. We now repeat the evaluation of Equation 1 with the same inputs except using our new Hp value in Equation 2. This yields our corrected change in flow depth over x:
    d
    H/dxc = 6.5663e-05.
  5. We then combine the results of these two predictions in flow depth change to give our best solution to the ODE Equation 1 at the downstream node. We combine the values using the trapezoidal rule for Hi = H(i+1) – ((0.5) * (dH/dxp + dH/dxc) * dx), giving a predicted change in flow depth of 0.1972 m, for a depth at Hi of 20.8028 m (it was 21 m at the downstream node).
  6. repeat steps 2-5 solving for each node moving up the model domain until the final node is determined.

This method is fairly stable for most discharges, but may fail when discharge is very low. In thsi case, the backwater region becomes condensed, and the rate of change in H becomes very large over a very small distance. My code for the predictor corrector implementation can be found as the get_backwater_fixed() function within the complete backwater_fixed model. Below is a gif showing the results of a range of input discharges to our model.

 

and a still multi-surface example to demonstrate the variability.

 

The low and moderate discharge water surface curves in the above figure (solid and dashed lines) demonstrate the classical convex-up (aka M1, e.g., Chow, 1959) condition that characterizes lowland delta systems during most of the time. The third, high discharge, water surface profile exemplifies a convex-down water surface profile. This condition, called the M2 condition has been recently demonstrated to have importance to the cyclic processes of avulsion and delta-lobe growth (e.g., Chatanantavet et al, 2012; Ganti et al., 2016).

 

Building a simple delta numerical model: Part III

 

References:
1. Nittrouer et al., Spatial and temporal trends for water-flow velocity and bed-material sediment transport in the lower Mississippi River. 2012. Geological Society of America Bulletin (Table 1).
2. Chow, Ven Te. Open Channel Hydaulics. N.p., 1959. Print. McGraw-Hill Civil Engineering Series.
3. Chatanantavet, Phairot, Michael P. Lamb, and Jeffrey A. Nittrouer. Backwater Controls of Avulsion Location on Deltas. 2012. Geophysical Research Letters 39.1
4. Ganti, V., A. J. Chadwick, H. J. Hassenruck-Gudipati, B. M. Fuller, and M. P. Lamb. Experimental River Delta Size Set by Multiple Floods and Backwater Hydrodynamics. 2016. Science Advances 2 (5).

This material is based upon work supported by the National Science Foundation (NSF) Graduate Research Fellowship under Grant No.145068 and NSF EAR-1427177. Any opinion, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation.

Building a simple delta numerical model: Part I

This is the first in a series I’m going to write over an undetermined-number-of-parts series where we will develop all the pieces to a simple delta numerical model. I’ll outline all the pieces here while I work up an interactive version with a GUI in Matlab, and we write pieces of the code together within the posts.

——————————————————————————–

 

The water depth (H) over a channel bed with a fixed-elevation downstream boundary can be calculated by a mass-and-momentum conservative derivation following from the full Navier-Stokes equations (e.g., Chow 1959). The so-called backwater equation, in one form, is presented as (Equation 1)
backwater_fixed_eqnwhere H is the flow depth, x is the streamwise coordinate of the flow, S is the channel bed slope, Cf  is the dimensionless coefficient of friction (corresponding to form drag in the channel bed and walls (i.e., roughness and bedforms)), and Fr is the Froude number, which scales with the ratio of inertia of the flow to the gravitational field driving the flow and can be given as (Equation 2)where qw = Qw is the width averaged water discharge, and g is the gravitational constant. Equations 1 and 2 are derived for a width-averaged, constant flow width scenario.

Equation 1 is useful to the research we do as scientists of lowland depositional systems because it predicts changes in flow depth through a delta system. The equation is solved with a boundary condition of a known flow depth (H) at the fixed-elevation downstream “receiving basin” boundary. For variations in river conditions (i.e., river water discharge), the surface elevation of receiving basins of large lowland rivers are effectively fixed, therefore the equation can be used to estimate a water surface over the lower reaches of the rivers we study for any input discharge conditions!

bw_schem_simp

With a calculation of H, we can then use a conservation of water equation Qw = U A (where U is flow velocity and A = B H is channel cross sectional area for an approximately rectangular channel), to evaluate the flow velocity at all points along the channel. Calculation of U in turn allows for calculation of sediment transport, and ultimately sediment deposition — but more on these parts in future parts of this series!

Equation 1 is valid for a solution where width (B) is fixed over the downstream length of x. Where width is roughly constant, say within the lower reaches of a channel we can use this simple form of the backwater equation. However, where width is not constant over all x (i.e., dB/dx != 0), say in the river plume beyond the channel mouth, we must retain an addition term from the derivation from the Navier-Stokes equations to account for this change in width. Since we’re using computers to solve the equations, and the dB/dx term is basically only one extra gradient calculation, this will an easy addition to our model in the future. I’ll write a separate post and link it here with a solution for that version of the backwater equation as well.

So how do we solve Equation 1? Let’s see what we know: the elevation of the receiving basin is fixed at z = 0. Therefore, if we know the channel bed profile, we know at the downstream boundary for ALL possible values of Qw. We can evaluate Equation 1 from the known downstream boundary, and knowing all variables on the right hand side at this boundary, calculate the change in flow depth moving upstream over the channel bed (dH/dx)!

The solution to Equation 1 (or in its slightly more complex form for a varying width domain) can be numerically estimated pretty easily by a predictor-corrector scheme. We’ll work up a calculation for a fixed-width form of the backwater equation (Equation 1) in the next post, and then proceed to use this as one module of our simple delta model.

Building a simple delta numerical model: Part II

 

This material is based upon work supported by the National Science Foundation (NSF) Graduate Research Fellowship under Grant No.145068 and NSF EAR-1427177. Any opinion, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation.